View TDA8566Q5_1005251.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

INTEGRATED CIRCUITS
DATA SHEET
TDA8566Q 2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
Product specification Supersedes data of 2000 Jan 28 File under Integrated Circuits, IC01 2001 Feb 21
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
FEATURES * Differential inputs * Very high Common Mode Rejection Ratio (CMRR) * High common mode input signal handling * Requires very few external components * High output power * 4 and 2 load driving capability * Low offset voltage at output * Fixed gain * Diagnostic facility (distortion, short-circuit and temperature pre-warning) * Good ripple rejection * Mode select switch (operating, mute and standby) * Load dump protection * Short-circuit proof to ground, to VP and across the load QUICK REFERENCE DATA SYMBOL VP IORM Iq(tot) Istb Isw Zi Pout SVRR cs CMRR Gv Vno PARAMETER operating supply voltage repetitive peak output current total quiescent current standby current switch-on current input impedance output power supply voltage ripple rejection channel separation common mode rejection ratio closed loop voltage gain noise output voltage Rs = 0 RL = 4 ; THD = 10% RL = 2 ; THD = 10% Rs = 0 Rs = 10 k CONDITIONS MIN. 6 - - - - 100 - - - - - 25 - GENERAL DESCRIPTION * Thermally protected * Reverse polarity safe
TDA8566Q
* Low power dissipation in any short-circuit condition
* Protected against electrostatic discharge * No switch-on/switch-off plop * Flexible leads * Low thermal resistance.
The TDA8566Q is an integrated class-B output amplifier contained in a 17-lead single-in-line (SIL; bent to DIL) plastic power package. The device contains 2 amplifiers in a Bridge-Tied Load configuration (BTL). The output power is 2 x 25 W in a 4 load or 2 x 40 W in a 2 load. It has a differential input stage and 2 diagnostic outputs. The device is primarily developed for car radio applications.
TYP. 14.4 - 115 0.1 - 120 25 40 60 50 75 26 -
MAX. 18 7.5 - 10 40 - - - - - - 27 120
UNIT V A mA A A k W W dB dB dB dB V
ORDERING INFORMATION TYPE NUMBER TDA8566Q PACKAGE NAME DBS17P DESCRIPTION plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm) VERSION SOT243-1
2001 Feb 21
2
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
BLOCK DIAGRAM
VP1
handbook, full pagewidth
TDA8566Q
VP2 13
IN1+
1 + 2 -
mute switch
5 CM
IN1-
6 2.3 k + - 2.3 k mute switch (9x) CM VA
OUT1+
+ -
8 60 k 60 k 2.3 k + - 2.3 k (9x) n.c. 9 standby switch 14 VA
OUT1-
MODE
TDA8566Q
Vref SGND 3 1x DIAG mute reference voltage + 17 - 10 2.3 k + - 2.3 k mute switch (9x) CM VA OUT2+ mute switch 15 DIAG VA standby reference voltage mute switch
CLIP
4
CLIP
60 k IN2+ 16
60 k
CM
IN2-
+ -
12 2.3 k + - 2.3 k 11 7 (9x)
MGD105
VA
OUT2-
PGND2
PGND1
Fig.1 Block diagram.
2001 Feb 21
3
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
PINNING SYMBOL IN1+ IN1- SGND CLIP VP1 OUT1+ PGND1 OUT1- n.c. OUT2+ PGND2 OUT2- VP2 MODE DIAG IN2+ IN2- PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 DESCRIPTION channel 1 input positive channel 1 input negative small signal ground clip detection supply voltage 1 channel 1 speaker output positive channel 1 negative power supply (ground) channel 1 speaker output negative not connected channel 2 speaker output positive channel 2 negative power supply (ground) channel 2 speaker output negative supply voltage 2 mode select switch (standby/mute/operating) short-circuit and temperature pre-warning diagnostic channel 2 input positive channel 2 input negative
MGD101
TDA8566Q
handbook, halfpage
IN1+ IN1- SGND CLIP VP1 OUT1+ PGND1 OUT1- n.c.
1 2 3 4 5 6 7 8 9
TDA8566Q
OUT2+ 10 PGND2 11 OUT2- 12 VP2 13 MODE 14 DIAG 15 IN2+ 16 IN2- 17
Fig.2 Pin configuration.
FUNCTIONAL DESCRIPTION The TDA8566Q contains 2 identical amplifiers and can be used for BTL applications. The gain of each amplifier is fixed at 26 dB. Special features of this device are: 1. Mode select switch 2. Clip detection 3. Short-circuit diagnostic 4. Temperature pre-warning 5. Open-collector outputs 6. Differential inputs. Mode select switch (pin 14) * Standby: low supply current * Mute: input signal suppressed * Operating: normal on condition.
Since this pin has a very low input current (<40 A), a low cost supply switch can be applied. To avoid switch-on plops, it is advisable to keep the amplifier in the mute mode for a period of 150 ms (charging the input capacitors at pins 1, 2, 16 and 17). This can be realized by microcontroller control or by an external timing circuit (see Fig.7). Clip detection (pin 4) When clipping occurs at one or more output stages, the dynamic distortion detector becomes active and pin 4 goes LOW. This information can be used to drive a sound processor or a DC volume control to attenuate the input signal and so limit the level of distortion. The output level of pin 4 is independent of the number of channels that are being clipped. The clip detection circuit is disabled in a short-circuit condition, so if a fault condition occurs at the outputs, pin 4 will remain at a HIGH level. The clip detection waveforms are illustrated in Fig.3.
2001 Feb 21
4
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
Short-circuit diagnostic (pin 15) When a short-circuit occurs at one or more outputs to ground or to the supply voltage, the output stages are switched off until the short-circuit is removed and the device is switched on again (with a delay of approximately 20 ms after the removal of the short-circuit). During this short-circuit condition, pin 15 is continuously LOW. When a short-circuit occurs across the load of one or both channels, the output stages are switched off for approximately 20 ms. After approximately 50 s the load condition is again checked to see if the short-circuit is still present. Due to this duty cycle of 50 s/20 ms the average current consumption during this short-circuit condition is very low (approximately 40 mA). During this short-circuit condition, pin 15 is LOW for 20 ms and HIGH for 50 s (see Fig.4). The power dissipation in any short-circuit condition is very low. Temperature pre-warning (pin 15)
TDA8566Q
When the junction temperature (Tvj) reaches 145 C, pin 15 will become continuously LOW. Open-collector outputs Pins 4 and 15 are open-collector outputs, therefore more devices can be tied together. Pins 4 and 15 can also be tied together. An external pull-up resistor is required. Differential inputs The input stage is a high-impedance fully differential balanced input stage that is also capable of operating in a single-ended mode with one of the inputs capacitively coupled to an audio ground. It should be noted that if a source resistance is added (input voltage dividers) the CMRR degrades to lower values.
handbook, halfpage out
V
MGD103
0
V4 VP 0 t
Fig.3 Clip detection waveforms.
handbook, full pagewidthcurrent
in output stage
MGA707
V15 VP
short-circuit over the load 20 ms
t
t 50 s
Fig.4 Short-circuit diagnostic timing diagram.
2001 Feb 21
5
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
LIMITING VALUES In accordance with the Absolute Maximum Rating System (IEC 134). SYMBOL VP PARAMETER supply voltage CONDITIONS operating non-operating during 50 ms; load dump protection trise 2.5 ms IOSM IORM Tstg Tvj Tamb Vpsc Vpr Ptot non-repetitive peak output current repetitive peak output current storage temperature virtual junction temperature ambient temperature short-circuit safe voltage reverse polarity total power dissipation - - - - - -55 - -40 - - - MIN.
TDA8566Q
MAX. 18 30 45 10 7.5 +150 150 +85 18 6.0 60 V V V A A
UNIT
C C C V V W
QUALITY SPECIFICATION Quality specification in accordance with "UZW-FQ-611-E", if this type is used as an audio amplifier. The number of the quality specification can be found in the "Quality Reference Handbook". The handbook can be ordered using the code 9397 750 00192. THERMAL CHARACTERISTICS Thermal characteristics in accordance with (IEC 747-1). SYMBOL Rth(j-c) Rth(j-a) PARAMETER thermal resistance from junction to case thermal resistance from junction to ambient in free air CONDITIONS VALUE 1.3 40 UNIT K/W K/W
handbook, halfpage
output 1
output 2
virtual junction
2.2 K/W
2.2 K/W
0.2 K/W
MEA861 - 1
case
Fig.5 Equivalent thermal resistance network.
2001 Feb 21
6
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
DC CHARACTERISTICS VP = 14.4 V; Tamb = 25 C; measured in test circuit of Fig.6; unless otherwise specified. SYMBOL Supply voltage VP Iq Vms(op) I14 Vo Vos Vms(mute) Vo Vos Vos Vms(stb) Istb Diagnostic V15 Tvj Notes 1. The circuit is DC adjusted at VP = 6 to 18 V and AC operating at VP = 8.5 to 18 V. 2. At VP = 18 to 30 V the DC output voltage 0.5 VP. diagnostic output voltage temperature pre-warning during any fault condition V15 = 0.6 V - - - 145 supply voltage quiescent current mode select switch level mode select switch current output voltage output offset voltage mode select switch level output voltage output offset voltage DELTA output offset voltage mode select switch level standby current note 1 RL = 6 - 8.5 - - - 3.3 - - - 0 - 14.4 115 - 15 7.0 - - 7.0 - - - 0.1 PARAMETER CONDITIONS MIN. TYP.
TDA8566Q
MAX. 18 180 VP 40 - 100 6.4 - 60 60 2 10 0.6 -
UNIT V mA V A V mV V V mV mV V A V C
Operating condition V14 = 14.4 V note 2
Mute condition note 2 mute/operating
Standby condition
AC CHARACTERISTICS VP = 14.4 V; Tamb = 25 C; RL = 2 ; fi = 1 kHz; measured in test circuit of Fig.6; unless otherwise specified. SYMBOL Pout PARAMETER output power CONDITIONS THD = 0.5% THD = 10% THD = 30% VP = 13.5 V; THD = 0.5% VP = 13.5 V; THD = 10% THD = 0.5%; RL = 4 THD = 10%; RL = 4 THD = 30%; RL = 4 VP = 13.5 V; THD = 0.5%; RL = 4 VP = 13.5 V; THD = 10%; RL = 4 MIN. 25 33 45 - - 16 21 28 - - 30 40 55 25 35 19 25 35 14 22 TYP. - - - - - - - - - - MAX. UNIT W W W W W W W W W W
2001 Feb 21
7
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
SYMBOL THD PARAMETER total harmonic distortion CONDITIONS Pout = 1 W note 3; V4 = 0.6 V Pout = 1 W; RL = 4 B fl fh Gv SVRR power bandwidth low frequency roll off high frequency roll off closed loop voltage gain supply voltage ripple rejection on; note 2 mute; note 2 standby; note 2 Zi Zi Vno input impedance input impedance mismatch noise output voltage on; B = 20 Hz to 20 kHz; Rs = 0 on; B = 20 Hz to 20 kHz; Rs = 10 k mute; B = 20 Hz to 20 kHz; independent of Rs cs Gv Vo CMRR channel separation channel unbalance output signal voltage in mute common mode rejection ratio Vi = Vi(max) = 1 V (RMS) Rs = 0 ; note 4 Rs = 45 k; note 5 Pout = 25 W; Rs = 10 k differential single-ended THD = 0.5%; Pout = -1 dB with respect to 25 W -1 dB; note 1 -1 dB - - - - - 20 25 50 50 80 100 50 - - - - 45 - - 60 40 MIN. 0.1 8 0.05 20 to 20000 25 - 26 - - - 120 60 2 85 100 60 - - - 75 - TYP.
TDA8566Q
MAX. - - - - - - 27 - - - 150 75 - 120 - - - 1 2 - -
UNIT % % % Hz Hz kHz dB dB dB dB k k % V V V dB dB mV dB dB
Notes 1. Frequency response externally fixed. 2. Vripple = Vripple(max) = 2 V (p-p); Rs = 0 . 3. Dynamic Distortion Detector (DDD) active; pin 4 is LOW. 4. Common mode rejection ratio measured at the output (over RL) with both inputs tied together; Vcommon 3.5 V (RMS); f = 100 Hz to 10 kHz; Rs = 0 . 5. Common mode rejection ratio measured at the output (over RL) with both inputs tied together; Vcommon 3.5 V (RMS); f = 1 kHz; Rs = 45 k. The mismatch of the input coupling capacitors is excluded.
2001 Feb 21
8
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
TEST AND APPLICATION INFORMATION
TDA8566Q
handbook, full pagewidth
+ Vmode _ +1 Rs/2 220 nF 60 k 14 + - 5 13 6+ 100 nF 2200 F/16V
+V P= _ 14.4 V
Vin1 Rs/2 220 nF _2 60 k - +
TDA8566Q
8_
RL1 VP 10 k VP 10 k CLIP
Vref + 3 + 16 Rs/2 Vin2 Rs/2 220 nF 60 k _ 17 - + 220 nF 60 k - + -
CLIP DETECTOR DIAGNOSTIC INTERFACE
4
15
DIAG
10 +
RL2 12 _ 7 11
MGD104
Fig.6 Stereo BTL test diagram.
Application notes DIAGNOSTIC OUTPUT Special care must be taken in the PCB layout to separate pin 4 from pins 1, 2, 16 and 17 to minimize the crosstalk between the CLIP output and the inputs. MODE SELECT SWITCH To avoid switch-on plops, it is advisable to keep the amplifier in the mute mode during 150 ms (charging of the input capacitors at pins 1, 2, 16 and 17). The circuit in Fig.7 slowly ramps-up the voltage at the mode select switch pin when switching on and results in fast muting when switching off.
mode select switch 100 k +Vsupply
handbook, halfpage
S
10 k
100
47 F
MGD102
Fig.7 Mode select switch circuit.
2001 Feb 21
9
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
PACKAGE OUTLINE DBS17P: plastic DIL-bent-SIL power package; 17 leads (lead length 12 mm)
TDA8566Q
SOT243-1
non-concave D x Dh
Eh
view B: mounting base side
d
A2
B j E A
L3
L
Q c vM
1 Z e e1 bp wM
17 m e2
0
5 scale
10 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A 17.0 15.5 A2 4.6 4.4 bp 0.75 0.60 c 0.48 0.38 D (1) 24.0 23.6 d 20.0 19.6 Dh 10 E (1) 12.2 11.8 e 2.54 e1 e2 Eh 6 j 3.4 3.1 L 12.4 11.0 L3 2.4 1.6 m 4.3 Q 2.1 1.8 v 0.8 w 0.4 x 0.03 Z (1) 2.00 1.45
1.27 5.08
Note 1. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT243-1 REFERENCES IEC JEDEC EIAJ EUROPEAN PROJECTION
ISSUE DATE 97-12-16 99-12-17
2001 Feb 21
10
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
SOLDERING Introduction to soldering through-hole mount packages This text gives a brief insight to wave, dip and manual soldering. A more in-depth account of soldering ICs can be found in our "Data Handbook IC26; Integrated Circuit Packages" (document order number 9398 652 90011). Wave soldering is the preferred method for mounting of through-hole mount IC packages on a printed-circuit board. Soldering by dipping or by solder wave The maximum permissible temperature of the solder is 260 C; solder at this temperature must not be in contact with the joints for more than 5 seconds.
TDA8566Q
The total contact time of successive solder waves must not exceed 5 seconds. The device may be mounted up to the seating plane, but the temperature of the plastic body must not exceed the specified maximum storage temperature (Tstg(max)). If the printed-circuit board has been pre-heated, forced cooling may be necessary immediately after soldering to keep the temperature within the permissible limit. Manual soldering Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is less than 300 C it may remain in contact for up to 10 seconds. If the bit temperature is between 300 and 400 C, contact may be up to 5 seconds.
Suitability of through-hole mount IC packages for dipping and wave soldering methods SOLDERING METHOD PACKAGE DIPPING DBS, DIP, HDIP, SDIP, SIL Note 1. For SDIP packages, the longitudinal axis must be parallel to the transport direction of the printed-circuit board. suitable suitable(1) WAVE
2001 Feb 21
11
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
DATA SHEET STATUS DATA SHEET STATUS Objective specification PRODUCT STATUS Development DEFINITIONS (1)
TDA8566Q
This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product.
Preliminary specification
Qualification
Product specification
Production
Note 1. Please consult the most recently issued data sheet before initiating or completing a design. DEFINITIONS Short-form specification The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 60134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. DISCLAIMERS Life support applications These products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no licence or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified.
2001 Feb 21
12
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
NOTES
TDA8566Q
2001 Feb 21
13
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
NOTES
TDA8566Q
2001 Feb 21
14
Philips Semiconductors
Product specification
2 x 40 W/2 stereo BTL car radio power amplifier with differential inputs and diagnostic outputs
NOTES
TDA8566Q
2001 Feb 21
15
Philips Semiconductors - a worldwide company
Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: Philips Hungary Ltd., H-1119 Budapest, Fehervari ut 84/A, Tel: +36 1 382 1700, Fax: +36 1 382 1800 India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 5F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2451, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 60/14 MOO 11, Bangna Trad Road KM. 3, Bagna, BANGKOK 10260, Tel. +66 2 361 7910, Fax. +66 2 398 3447 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 3341 299, Fax.+381 11 3342 553
For all other countries apply to: Philips Semiconductors, Marketing Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 2001
Internet: http://www.semiconductors.philips.com
SCA 71
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
753503/05/pp16
Date of release: 2001
Feb 21
Document order number:
9397 750 07883

▲Up To Search▲

Price & Availability of TDA8566Q5

	To Download TDA8566Q5 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .